Fibroblast

Fibroblast device uses plasma, an ionized gas between the tip of the Fibroblast tool and patients skin. During the procedure electric arc forms, referred to as a plasma flash or mini lightning. Only surface of the skin is touched causing tissue to retract. This is known as sublimation, the process of turning solid directly to gas. Targeted tissue sublimate, therefore no damage to surrounding areas or deeper skin layers. Patient can resume regular activities right away with minimal discomfort

Yes. Anyone interested in Fibroblast procedure is required to have face-to-face consultation. Careful assessment specialist will ensure the right treatment plan.. My goal is to keep clients informed and meet their expectations.

When activated, Fibroblast tool creates plasma flash which travels from the tool’s tip to treated area. The tool itself never touches the skin however plasma flash creates a tiny dot upon the contact. Further points are applied creating a symmetrical grid over the treatment area. This in effect causes tightening of skin fibers. Only surface of the skin is affected and deeper layer known as the basal lamina is not. Fibroblast is non-invasive treatment, no cuts to the skin or stitching is necessary. Fibroblast is completely bloodless and without unnecessary damages to surrounding tissues.

To minimize any discomfort numbing cream will be applied to the treatment area. It will take 20-25 minutes for anesthetic to take effect. The procedure itself takes between 20-30 minutes depending on the size of treated area. The appointment shouldn’t last longer then 1 hour.

Fibroblast is non-surgical treatment with no pain or minimal discomfort reported by patients. Topical cream is applied to numb treated area prior to procedure. Immediately after the treatment the skin will be reddened and lightly swollen. This will usually last up to 3 days, although slight redness may remain for up to 2 weeks. During the procedure carbon crusts will form on the skin directly where Fibroblast tool was applied. Crusts should not be touched for 5-7 days however post-procedure foundation can be used to camouflage them. To minimize complications you will be informed on proper aftercare following the procedure.

Fibroblast is very safe and side-effects are rare but infection, scarring and temporary change of skin pigmentation may occur. Mild swelling is expected during first 3 days and usually entirely gone by day 5. Majority of our patients do not report any of those after a week. In some rare occasions complications may occur. Please inform your Fibroblast specialist immediately in case of any unusual symptoms. This may include signs of infection such as excessive redness, pus, blistering or thick, yellow crust forming in treatment area.

Yes. It is very important to follow our after care recommendations. Carbon crusts CANNOT be scratched or removed. Drying skin by dabbing with a clean, lint-free cloth is allowed. Healing skin should be protected from direct sun with SPF50 cream. Make up, sports, swimming and sauna are not permitted until crusts fall off. This should happen within 7 days of procedure.

There are no specific requirements before the treatment. We suggest not to apply any cosmetics before the procedure. You should tell your practitioner about any recent medical conditions and medications taken. Mention any surgeries or aesthetic procedures performed currently on your skin.

Most patients should notice the effect of the procedure right away. However the healing will continue and the full result should be visible within 4-6 weeks. In some cases patients may need more then one treatment. This depends on treatment area and skin condition.

The treatment should last long term rather then few months although it is hard to predicted exactly. Aging is dynamic process and there are many factors affecting patients individually. Lifestyle, diet and genetics just to mention few. After Fibroblast procedure or traditional surgery your skin will be a subject to aging. Your skin will continue to relax (loosen) again. In some rare situations aging may be accelerated and effectiveness of Fibroblast would be shortened. I will discuss those conditions, so patients have better understanding of what to expect.

Yes, it is certified by European CE. This means product meets high safety, health and environmental protection requirements. Fibroblast treatment is already extremely popular across Europe. It quickly becomes choice for those looking into a non-surgical skin lift. Only Fibroblast technicians who underwent specialized training and hold the Fibroblast Certification are authorized to perform treatments. You will be asked to fill in and sign consent. All potential side effects will be carefully explained.

In some cases just one treatment may be sufficient, especially with lighter corrections. Many of the treatments will depend on a size of the treated area and customer’s desired degree of correction. Full effect of the first treatment will be visible after 4-6 weeks following the procedure. If patient requires additional treatment to achieve optimal results those should be scheduled at 6 to 8 weeks intervals.

Fibroblast can be used for many different skin conditions. Eyelid tightening, body lifting, acne treatment, scar correction and stretch marks. If you suffer from any of the above conditions but hesitated with traditional surgical procedures, non-invasive Fibroblast treatment may be the right treatment for you.